DELL DIMENSIONS E510 AUDIO DRIVER

Ground yourself by touching an unpainted metal surface on the back of the computer. You can do so by touching an unpainted metal surface on the computer chassis. Do not route card cables over or behind the cards. Otherwise, your computer may not start properly. If you are replacing a hard drive that contains data you want to keep, back up your files before you begin this procedure. Gently pull the securing tab, grasp the card by its top corners, and then ease it out of its connector.

Uploader: Dir
Date Added: 4 February 2010
File Size: 33.52 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 58505
Price: Free* [*Free Regsitration Required]

Dimenssions sound is there, but it cracks every now and then, cuts off, and on low-quality, old speakers, the sound is muffled when you first play it but that could be the speakers. Flaming or offending other users Illegal activities: Sorry, there was a problem flagging this post.

You must route the DC power cables properly through the routing clips when you replace the cables to prevent them from being pinched or crimped. When installing the heat-sink assembly, do not touch the thermal interface on its underside, as this may result in damage. FlexBay for optional floppy drive or optional Media Card Reader. This one tip will help you sleep better tonight A few seconds are all you need to get a better night’s rest.

To guard against electrical shock, always unplug your computer from the electrical outlet before removing the cover. Ensure that the tab on the processor cover is positioned underneath the release lever at the front of the socket.

Sound And Speaker Problems; No Sound From Speakers – Dell Dimension Owner’s Manual [Page 43]

Disable onboard and use anything else. Note the routing of the DC power cables underneath the routing clips in the computer frame as you remove them from the system board and drives. To connect a network cable, first plug the cable into the network port or device and then plug the cable into the computer. When removing an IDE drive data cable, grasp the colored pull-tab and pull until the connector detaches. If your computer includes a card retention mechanism, remove the top of the retention mechanism by pressing the tab and pulling up on the top.

  FUJI XEROX DOCUMENT CENTRE 186 DRIVER

Thank you for helping us maintain CNET’s great community. Reversing the cable prevents the drive from operating and could damage the controller, the drive, or both. The sliding plate secures and releases the drive panel and helps to secure the drives. See the documentation that came with the card for information on configuring the card, making internal connections, or otherwise customizing it for your computer.

The pin-1 end of a connector on a board or a card is usually indicated by a silk-screened “1” printed directly on the board or card. Remove the card before connecting the floppy-drive cables.

To loosen the two captive screws on each side of the heat-sink assembly, you need a long Phillips screwdriver. Most interface connectors are keyed for correct insertion; that is, a notch or a missing pin on one dimensionns matches a tab or a filled-in hole on the other connector.

Dell Dimension 5150 Owner’s Manual: Sound And Speaker Problems; No Sound From Speakers

If you are not installing a processor upgrade kit from Dell, reuse the original heat-sink assembly when you install your new processor. See the documentation that came with the drive for instructions on installing any software required for drive operation. You can do so by touching an unpainted metal surface on the computer.

  GM965 LAN DRIVER DOWNLOAD

See the documentation for the card for information about the card’s cable connections. If you installed a processor replacement kit from Dell, return the original heat-sink assembly and processor to Dell in the same package in which your replacement kit was sent. Instead, set the drive on a surface, such as a foam pad, that will sufficiently cushion it.

When you connect two IDE devices to a single IDE interface cable and configure them for the cable select setting, the device attached to the last connector on the interface cable is the master or boot device drive 0and the device attached to the middle connector on the interface cable is the slave device drive 1. Do not install ECC or buffered memory modules. While you work, periodically touch an dimemsions metal surface to dissipate any static electricity that could harm internal components.

Ensure that you release the securing tab to unseat the card. If the card is not removed correctly, the system board may be damaged.

Ground yourself by touching an unpainted metal surface on the back of the computer. To connect a network cable, first plug the cable into the network port or device, and then plug the cable into the computer. To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of your computer’s electronic components.